Oil Iran

Volvo loader L90 and L120 wheel oil seal

The wheel oil seal in Volvo L90 and Volvo L120 is installed at the interface between the wheel hub and the front or rear axle housing. It is positioned outboard of the tapered roller bearings and inboard of the hub flange. Its primary function is to retain differential oil and prevent the ingress of dust, water, and abrasive particles. The inner diameter typically ranges from 110 mm to 160 mm depending on axle configuration. Seal width is generally between 15 mm and 25 mm. Lip materials are commonly NBR or FKM, with thermal resistance up to 120 degrees Celsius. Internal pressure is usually below 0.5 bar, while shaft peripheral speed can reach 8 m per second. The garter spring provides a consistent radial load of approximately 15 to 25 N.

From an engineering perspective, the wheel hub seal operates through controlled interference between the elastomeric sealing lip and a hardened shaft surface. The recommended shaft surface roughness is Ra 0.2 to 0.8 microns to minimize wear and heat generation. Contact surface hardness is typically 55 to 60 HRC to resist scoring and micro pitting. Bearing radial play exceeding 0.3 mm can accelerate leakage and reduce seal service life. Under heavy mining conditions, average seal durability ranges from 4000 to 8000 operating hours. Proper insta

Araz Sanat B400s 400,000 Steel Boiler Room Hot Water Boiler

The Araz Sanat B400s steel hot water boiler delivers a nominal thermal capacity of 400,000 kcal/h. This unit is optimized for operation with natural gas and diesel fuel. Its combustion efficiency exceeds 89 percent. The boilers maximum allowable working pressure is 6 bar. It is constructed from low-carbon ST37 steel plates. The thickness of the main body plates is precisely calculated for different sections. The boiler features a three-pass smoke tube design with a wet-back configuration. This structure maximizes heat transfer efficiency. Its heating surface area is approximately 12 square meters. All seams and connections are tested using argon welding methods. This process guarantees structural integrity and quality.

This hot water boiler is manufactured in compliance with the EN 12953 international standard. The body is insulated with refractory rock wool with a density of 120 kg/m³. The external cladding consists of 0.6 mm thick galvanized sheet. It is equipped with an atmospheric burner capable of capacity modulation. The output water temperature is controlled within a range of 70 to 90 degrees Celsius. Key components include a cylindrical furnace and a combustion chamber. The overall dimensions are approximately 250 by 120 by 120 centimeters. This product is suitable fo

Oil-Inject Rotary Screw Compressors

Oil-injected screw compressors utilize duplex 2205 steel alloy for heavily loaded rotors. An asymmetric 5+6 helical profile is precision-machined onto male and female rotors with 0.001 mm geometric accuracy. Their air delivery capacity spans 22 to 355 kW, equivalent to 3.2 to 65 m³/min at 7-15 bar working pressure. The oil injection system operates at 4-6 bar pressure with 0.8 to 12 L/min flow rate. Discharge air temperature is maintained within 10°C above ambient via an intelligent temperature control system. Nominal volumetric efficiency reaches 94%, with isothermal efficiency up to 68%. A smart PID controller optimizes specific energy consumption below 0.11 kW per cubic meter.

The core structure features a GG30 grade cast iron housing with integrally cast cooling fins. A four-stage oil separation system cyclone and coalescing reduces oil concentration below 2 ppm. An intelligent piston-type capacity regulator controls flow with 0.7-second response time and 0.1% positioning accuracy. Shell-and-tube heat exchangers with aluminum fins provide 85% heat transfer efficiency. A forced lubrication system with 3-micron filtration and dedicated cooler extends oil life to 8,000 hours. Advanced acoustic design achieves 65-70 dB sound pressure level at 1 meter distance. The complete p

heli coil

A Helicoil is a metallic threaded insert for repairing and reinforcing damaged internal threads. It is made from Austenitic stainless steel wire such as AISI 302/304 or Inconel X-750 alloy with a square or diamond cross-section. The wire diameter typically ranges from 0.6 to 2 mm, graded according to ISO 9001:2015. Helicoils are available in metric M2 to M48 and unified UNC/UNF thread sizes. The ultimate tensile strength of standard steel inserts is at least 1400 MPa. Installation requires creating a starter thread using a special drill and tap steyer. After installation, the inserts back-out torque is up to 40% higher than the original threads. This feature secures the connection against vibration-induced loosening.

The Helicoil structure is a spring-like coil with a 90-degree wind angle and a short lead-in tang. Surface coatings like silver or PTFE are sometimes used to reduce friction and improve electrical properties. According to aerospace standards like NASM 33575 or MS 21209, it must withstand temperature cycles from -55°C to +260°C. Quality control tests include torsional tension, sealing tests, and salt spray corrosion resistance checks. Its primary applications are in aircraft engines, braking systems, and aluminum cylinder blocks. The inserts are permanently locke

Ferroli Pegasus D45K130 floor-standing storage boiler

The Ferroli Pegasus D45K130 floor-standing storage boiler, with a heating capacity of 38 kW, is one of Ferroli’s most powerful models, ideal for large homes and villas with high heating and hot water demands. It features a dual heat exchanger system: a primary cast-iron heat exchanger resistant to corrosion and high temperatures, and a secondary stainless steel exchanger for instant domestic hot water production. The boiler achieves approximately 91% thermal efficiency, with a maximum heating circuit temperature of 80°C and a working pressure up to 3 bar. It includes a 130-liter enameled steel hot water tank with high-density insulation for minimal heat loss.

The Pegasus D45K130 is equipped with a fan-assisted burner, electronic flame control, frost protection, anti-pump seizure, and overheating protection systems. It can be connected to room thermostats for intelligent temperature management and operates on 230V single-phase electricity. The domestic hot water production rate is around 20 liters per minute with a 25°C temperature rise, suitable for multiple simultaneous outlets. Featuring a low-noise design, electrostatic powder-coated steel body, and compact form factor, this model ensures both performance and durability. The Ferroli Pegasus D45K130 complies with CE Euro

Deutz engine 1011 1012 and 1013 oil cooler

The engine oil cooler used in DEUTZ 912, 1011, 1012, and 1013 diesel engines is a critical thermal management component designed to stabilize lubricant temperature under continuous load. It operates based on controlled heat exchange between hot engine oil and ambient air or coolant flow. Under rated power conditions, the system is engineered to maintain oil temperature below approximately 105 to 115 degrees Celsius. The core typically features aluminum plate or tube fin construction with optimized surface area to ensure high heat dissipation efficiency and minimal pressure drop. Flow channels are dimensioned according to oil pump capacity, commonly supporting flow rates above 40 liters per minute depending on engine configuration.

In DEUTZ 912 to 1013 series engines, oil cooling efficiency directly influences bearing life, piston lubrication stability, and turbocharger durability. Thermal calculations consider Reynolds number, convective heat transfer coefficient, and oil viscosity variation across temperature ranges. Properly designed oil coolers limit pressure loss to typically less than 0.3 bar while sustaining consistent lubrication pressure. This controlled temperature environment reduces oxidation, prevents viscosity breakdown, and extends oil service intervals. As a res

deutz engine 912 1011 1012 and 1013 oil pump

In Deutz engine series 912, 1011, 1012 and 1013, the oil pump is a gear type positive displacement unit engineered to maintain stable oil pressure across varied loads. It is typically mounted at the front cover or lower engine block and driven by the crankshaft via a spur gear interface. Pump displacement varies by model: 912 pumps deliver approximately 60–80 liters per minute at 2000 rpm for 3-4 cylinder configurations, while 1012/1013 pumps deliver 90–120 liters per minute at similar speeds for 4–6 cylinder engines. Internal clearances are machined to within 0.02 mm tolerance to sustain oil film integrity at operating temperatures up to 120 °C. Relief valves are calibrated to open around 3.5–4.0 bar to protect bearings from excessive pressure spikes.

The cast aluminum housing of Deutz oil pumps integrates precision bored bores for idler and drive gears with an interference fit controlled to H7/s6 standards to reduce vibration. Pump inlet is sized to maintain Net Positive Suction Head NPSH with scavenge suction above 0.8 bar absolute, reducing cavitation risk. Pressure pulsation dampers are often incorporated to smooth delivery to main galleries feeding crankshaft and camshaft bearings. Successful lubrication limits journal metal temperature rise to under 30 °C abov

Oil-Inject Rotary Screw Compressors

The screw compressor consists of male and female rotors made from AISI 4140 forged steel with hard chrome plating. Rotor profile machining accuracy is within 0.005 mm with 0.03 to 0.08 mm clearance between them. Air delivery capacity ranges from 2.2 to 400 kW, equivalent to 0.35 to 70 cubic meters per minute. Standard working pressure is 7 to 13 bar, extendable to 20 bar in special designs. The oil injection system operates at 0.5 to 8 L/min flow rate with 40-90°C operating temperature. Volumetric efficiency is 88-94% with overall energy efficiency reaching 90%. Sound pressure level at one meter varies between 62 to 78 decibels. A digital PID controller monitors operating parameters with 0.1% accuracy.

The main structure features a GG25 cast iron housing with 15-40 mm wall thickness and integrated cooling fins. The dual cooling system includes oil-air and separate compressed air aftercoolers. A three-stage oil separator with 99.9% efficiency reduces oil content to 3 ppm. The capacity regulator uses slide valve or piston type with under 2-second response time. A two-stage intake air filter removes particles larger than 5 microns. Static and dynamic balancing design maintains vibration below 4.5 mm/s. Piping connections are hydrostatically tested for 25 bar pressure. Bearing an

Ferroli Divatop D F37D wall-hung boiler

The Ferroli Divatop D F37D wall-hung boiler, with a thermal capacity of 32 kW, is one of Ferroli’s top-performing models designed for large residential areas and high-demand heating applications. It features a copper primary heat exchanger with an anti-corrosion coating and a stainless steel plate secondary heat exchanger, ensuring fast and stable heat transfer. With an efficiency of approximately 93%, it delivers domestic hot water up to 60°C and heating water up to 80°C. The heating circuit supports up to 3 bar pressure, with an 8-liter expansion vessel. Its fan-assisted, electronically modulated burner ensures low gas consumption, quiet operation, and stable performance.

The Divatop D F37D includes a digital display and advanced safety systems such as frost protection, anti-pump lock, anti-temperature fluctuation, and automatic fault diagnostics. It can be connected to room thermostats and outdoor sensors for optimized energy management. The domestic hot water flow rate is about 17.5 liters per minute at a 25°C temperature rise, suitable for multiple simultaneous usage points. Weighing approximately 36 kg, its compact design allows easy installation even in confined spaces. The F37D model complies with European CE standards for safety, efficiency, and low noise operati

Oil-Inject Rotary Screw Compressors

Screw compressors are built from forged steel alloy with hard chrome-plated male and female rotors. The rotor length-to-diameter ratio typically ranges from 1.0 to 1.7, with a surface finish better than Ra 0.8 microns. Air delivery capacity varies from 10 to 5000 m³/h at working pressures of 7 to 13 bar. The rotors are synchronized with a timing accuracy of 0.001 seconds. A forced-feed oil lubrication system operates at 50 to 200 liters per minute. These compressors achieve a volumetric efficiency of up to 92%. Sound pressure level at one meter is typically maintained below 70 dBA. Discharge air temperature is controlled to 15°C above ambient via an oil cooling system.

The compressor structure features a cast iron housing with integrated cooling fins. A three-stage oil separation system removes oil particles with 99.9% efficiency. A PLC controller with a touchscreen display monitors performance and conditions. A load regulation valve with a 2-second response optimizes energy consumption. A two-stage intake air filter operates with 99.8% particle removal efficiency. The compressor is designed for up to 100,000 hours of operation under harsh conditions. An anti-pulsation and vibration dampening system limits vibration to under 4.5 mm/s. All piping connections are hydrostatical

Lorch Adena 32 kW wall-mounted boiler

The Lorch Adena 32 kW wall-mounted boiler is a dual heat exchanger system with a 32 kW output and approximately 92 percent thermal efficiency. Designed for residential and commercial spaces up to 200 square meters, it provides simultaneous space heating and domestic hot water. The primary heat exchanger is copper with an anti-scale coating, while the secondary is stainless steel to ensure efficient heat transfer and long-lasting durability. The fan-assisted electronic combustion system maintains stable performance and optimized gas consumption even at low gas pressures of 5 mbar. The heating circuit operates at 3 bar, and the domestic hot water flow rate reaches approximately 15 liters per minute at 35°C.

This boiler includes advanced safety features such as anti-freeze protection, automatic flame control, over-temperature protection, and safeguards against pressure fluctuations. The digital display provides real-time monitoring of temperature, pressure, and fault codes. Operating noise is below 39 dB, making it suitable for residential and commercial installation. The unit measures 770×420×310 mm and weighs approximately 35 kg. The Adena 32 kW model is compatible with smart thermostats and remote control systems and is engineered according to Class A energy efficiency stan

Volvo loader oil temperature sensor

The oil temperature sensor in Volvo L90 and L120 wheel loaders measures hydraulic or engine oil temperature accurately and transmits data to the ECU and cabin display. The sensor uses a resistive element with ±1°C accuracy and can monitor oil temperatures ranging from -20 to 120°C. It is typically installed in the oil return line to the tank or at the hydraulic pump outlet to capture real-time temperature under varying load conditions. Proper sensor operation is critical for protecting the pump, cylinders, and other hydraulic components, preventing overheating that can reduce oil viscosity and increase wear on moving parts.

For L90 and L120 loaders, oil temperature sensors are supplied with OEM part numbers VOE15153124 and VOE11419485, providing an output signal to the ECU in the range of 0.5–4.5 volts corresponding to temperature. These sensors can operate in oil flow rates between 150 and 200 liters per minute and withstand hydraulic pressures up to 280 bar. Installation, wiring, and functional testing according to Volvo standards ensure precise temperature control, reduce risk of hydraulic failure, and extend system life. OEM and high-quality aftermarket brands supply sensors made of corrosion-resistant steel and materials suitable for heavy-duty operation.

Oil-Inject Rotary Screw Compressors

Oil-injected screw compressors are manufactured from AISI 4340 forged steel with 58-62 HRC surface hardness. Male and female rotors feature a 4+6 asymmetric profile machined to 0.001 mm accuracy. Capacity ranges from 18.5 to 355 kW, delivering 3 to 65 cubic meters per minute. Nominal working pressure is 7 to 15 bar with maximum output pressure of 20 bar. The oil injection system operates at 0.7 to 1.2 liters per second flow rate. Discharge air temperature stabilizes within 10°C above ambient. These compressors achieve 94% volumetric efficiency and 65% isothermal efficiency. An intelligent PID controller maintains specific energy consumption below 0.12 kW per cubic meter.

The rotary mechanism operates at a fixed 11:1 compression ratio and 2970 RPM speed. The two-stage cooling system includes oil-water and oil-air heat exchangers. A triple-layer oil separator with 99.97% efficiency reduces oil content to 3 ppm. An intelligent piston-type capacity regulator responds within 0.8 seconds. Sound pressure level at 1 meter ranges between 68 to 72 decibels. The complete package includes a soft starter drive and a 5-micron particle filter. Mechanically balanced design allows installation on basic foundations. The design service life is 80,000 hours with full component reparability.

Lorch Artman 32 kW condensing wall-mounted boiler

The Lorch Artman 32 kW condensing wall-mounted boiler is a dual heat exchanger system with high thermal efficiency of approximately 94 percent and a 32 kW output. Designed for residential and commercial spaces up to 200 square meters, it provides simultaneous space heating and domestic hot water. The primary heat exchanger is copper with an anti-scale coating, while the secondary is stainless steel for optimal heat transfer and long-term durability. The fan-assisted electronic combustion system ensures stable operation and efficient gas consumption even at low gas pressures of 5 mbar. The heating circuit operates at 3 bar, and domestic hot water flow rate reaches 15 liters per minute at 35°C.

This condensing boiler includes comprehensive safety systems such as anti-freeze protection, automatic flame control, over-temperature protection, and pressure fluctuation safeguards. The digital display provides accurate monitoring of temperature, pressure, and system faults. Operating noise is below 39 dB, making it suitable for residential and commercial installation. The unit measures 770×420×310 mm and weighs approximately 35 kg. The Artman 32 kW model supports smart thermostats and remote control systems and is designed according to Class A energy efficiency standards.

Ferroli Divatop D F32D wall-hung boiler

The Ferroli Divatop D F32D wall-hung boiler, with a 28 kW heating capacity, is a high-efficiency and low-consumption model designed for medium to large residential spaces. It features a copper primary heat exchanger with an anti-corrosion coating and a stainless steel plate secondary heat exchanger for optimal thermal exchange between the heating and domestic hot water circuits. With an efficiency of around 93%, it provides heating water up to 80°C and domestic hot water up to 60°C. The heating circuit operates at pressures up to 3 bar, supported by an 8-liter expansion vessel. The fan-assisted, electronically modulated burner ensures quiet, stable, and fuel-efficient operation.

The Divatop D F32D includes a digital display and advanced safety systems such as frost protection, anti-pump seizure, temperature stabilization, and automatic fault diagnostics. It supports connection to room thermostats and outdoor sensors for enhanced energy efficiency. In hot water mode, it delivers approximately 15.3 liters per minute with a 25°C temperature rise. The unit weighs about 35 kg, and its compact design allows easy installation in confined spaces. Operating below 50 dB, the F32D complies with CE European standards for safety, performance, and environmental efficiency.